DERR-2024-006847

1
UNDERGROUND STORAGE TANK CLOSURE PLAN (rev. 7/13) FACILITY ID# 4000775 …
LHD USE ONLY
Date Received
Reviewer
Date LHD Approved
Date mailed to State
Closure Plan prepared at the request of the owner/operator (identified below) by Josie Messersmith
of (company name) Stantec Consulting Services, Inc. Phone #
Address City State Zip
A Contractor may prepare this Closure Plan as the owner/operator's agent. In preparing the Closure Plan, the Contractor must act with
the owner/operator's knowledge and approval. The owner/operator must sign the Closure Plan. Submit Closure Plan to: DERR/UST,
P.O. Box 144840, Salt Lake City, Utah, 84114-4840
This Closure Plan is submitted in compliance with the requirements contained in 40 CFR 280 Subpart G and R311-204 (U.A.C.)
Piping closure only Tank # 1 2A 2B
Tank Type (Steel,FRP,etc.) FRP FRP FRP
Piping Type (Steel,FRP,etc.) FRP FRP FRP
Date Installed 5/31/2014 5/31/2014 5/31/2014
Capacity 15000 8000 7000
Substance stored* GASOLINE GASOLINE DIESEL
Date last operated Currently in use
Removal/In Place/Change in
Service (CIS)?
*Indicate the specific substance stored in each tank to be closed (gasoline, diesel, new oil, waste oil, etc.)
For waste oil tanks: Have degreasing or other types of solvents been stored or mixed with the waste oil?
Yes (identify if known) . No Not Known
Analysis for lead or other contaminants may be required prior to disposal of contaminated soil or other material. (Check with your
disposal facility.)
STATE USE ONLY
Date Received
Date Mailed to LHD
Date Received From LHD
Reviewer/Date Approved
Mgr. Review/Date
FACILITY INFORMATION
Tank Owner TRMC Retail LLC Phone #
Address 500 Speedway Drive City Enon
State
OH Zip 45323
Facility Name Speedway No. 9414
Address 1344 FORT UNION BLVD City SLC
State
UT Zip 84121
Contact person Phone #
Total number of regulated underground tanks at this site 3
Total number of regulated underground tanks at this site to be closed 3
Currently in use Currently in use
RemovalRemoval Removal
2890 East Cottonwood Parkway, Suite 300 Salt Lake City UT 84121
5/3/2024
5/3/2024
2
Before the closure plan is submitted for approval, the local health and fire departments where the facility is located
must be contacted.
CONTACT LOCAL HEALTH DISTRICT: Name of Dist. Date
Contact Title Phone#
CONTACT LOCAL FIRE DEPT. Name of Dept. Date
Contact Title Phone#
DISPOSAL INFORMATION
Tank(s) will be disposed at: Facility
Address City State Zip
Contact person Phone#
Product lines will either be: removed or cleaned, secured in place, and capped.
Vent lines will either be: removed or cleaned and secured open.
Piping will be disposed at: Facility
Address City State Zip
Contact person Phone#
Tank(s) will be emptied by: company Phone#
Tank(s) will be cleaned by: company Phone#
Contaminated water in the tank/rinsate will be disposed at: Facility
Contact person Phone#
Tank(s) will be: purged or rendered inert by the following method:
Residual sludges will be disposed at the following facility:
Address City State Zip
Contact person Phone#
FOR CLOSURE IN PLACE ONLY
For this closure method, you are subject to the requirements of UAC R315-302-2(6), which requires annotating the property title and
submitting documentation to the Division of Solid and Hazardous Waste (DSHW). For information on how to comply with these
requirements, contact the DSHW Solid Waste Landfills Section Manager at [phone].
Approval for in-place closure has been granted by the Local Fire Department. (Must submit approval in writing with Closure Plan)
Fire Dept. Phone# Contact person Date
Approval for in-place closure has been granted by the Local Health Department.
Health Dept. Phone# Contact person Date
Substance to be used to fill tanks:
TANK REMOVER Name Cert. # TR Exp. Date
Company Phone #
Address City State Zip
SOIL/GROUNDWATER SAMPLER Name Cert. # GS Exp. Date
Company Phone #
Address City State Zip
x
x
Greg Neville -0244 10-1-2024
Pacific West Environmental and Infrastructure
1555 W 2200 S, Ste A Salt Lake City UT 84119
801-972-2727
Steve Yorgason 1630 4/15/2025
Stantec Consulting Services, Inc. [phone]
2890 East Cottonwood Parkway, Suite 300 Salt Lake City UT 84121
Salt Lake County Health Department 5/1/2024
Hayley Schaffer Environmental Health Supervisor [phone]
Unified Fire Authority 5/1/2024
Kendal Perry Hazmat Inspector [phone]
Salt Lake Valley Landfill
6030 W. California Ave. Salt Lake City UT 84104
Scale House [phone]
Salt Lake Valley Landfill
6030 W. California Ave. Salt Lake City UT 84104
Scale House [phone]
Pacific West Environmental and Infrastructure
Pacific West Environmental and Infrastructure
801-972-2727
801-972-2727
STC Industrial Services, Inc.
Shane Adolf [phone]
x Dry Ice
STC Industrial Services, Inc.
618 South 4050 West Salt Lake City UT 84104
Shane Adolf [phone]
3
SITE ASSESSMENT
A site assessment must be performed for all UST closures and change-in-service. Site assessments must be performed as outlined in 40 CFR
280.72 and R311-205 (U.A.C.). If contamination is suspected, additional samples must be collected at the location where contamination is
most likely to be present. If groundwater is encountered, a soil sample must be collected, in the unsaturated zone, in addition to each
groundwater sample. Soil and groundwater samples must be analyzed for the compounds shown in the following table, using appropriate lab
methods.
Substance or
Product Type
Contaminant Compounds to be Analyzed for Each
Substance or Product Type
ANALYTICAL METHODS1
Soil, Groundwater
or Surface Water
Gasoline
Total Petroleum Hydrocarbons (purgeable TPH as gasoline
range organics C6 - C10)
EPA 8015 or EPA 8260
Benzene, Toluene, Ethyl benzene, Xylenes, Naphthalene,
(BTEXN) and MTBE
EPA 8021 or EPA 8260
Diesel
Total Petroleum Hydrocarbons (extractable TPH as diesel
range organics C10 – C28)
EPA 8015
Benzene, Toluene, Ethyl benzene, Xylenes, and Naphthalene
(BTEXN)
EPA 8021 or EPA 8260
Used Oil
Oil and Grease (O&G) or
Total Recoverable Petroleum Hydrocarbons (TRPH)
EPA 1664 or
EPA 1664 (SGT*)
Benzene, Toluene, Ethyl benzene, Xylenes, Naphthalene
(BTEXN) & MTBE; and Halogenated Volatile Organic
Compounds (VOX)
EPA 8021 or EPA 8260
New Oil Oil and Grease (O&G) or
Total Recoverable Petroleum Hydrocarbons (TRPH)
EPA 1664 or
EPA 1664 (SGT*)
Other Type of analyses will be based upon the substance or product
stored, and as approved by the DERR Division Director
Method will be based upon the
substance or product type
Unknown
Total Petroleum Hydrocarbons (purgeable TPH as gasoline
range organics C6 - C10)
EPA 8015 or EPA 8260
Total Petroleum Hydrocarbons (extractable TPH as diesel
range organics C10 – C28)
EPA 8015
Oil and Grease (O&G) or
Total Recoverable Petroleum Hydrocarbons (TRPH)
EPA 1664 or
EPA 1664 (SGT*)
Benzene, Toluene, Ethyl benzene, Xylenes, and Naphthalene
(BTEXN) and MTBE; and Halogenated Volatile Organic
Compounds (VOX)
EPA 8021 or EPA 8260
1 The following modifications to these certified methods are considered acceptable by the DERR Division Director:
•Dual column confirmation may not be required for TPH and BTEXN/MTBE analysis.
•A micro-extraction or scale-down technique may be used for aqueous samples, but only for the determination of extractable TPH as diesel range
organics (C10 – C28).
•Hexane may be used as an extraction solvent.
•*Silica Gel Treatment (SGT) may be used in the determination of Total Recoverable Petroleum Hydrocarbons.
NOTE: The sample preparation method and any modification(s) to a certified method must be reported by the laboratory.
4
CONTAMINATED MATERIALS MUST BE DISPOSED AT AN ACCEPTABLE FACILITY:
All materials generated from UST closures must be managed and disposed in a manner that does not place those materials in direct contact
with the environment. On-site stockpiling of contaminated soils may be required prior to any soil management activities. Any person
providing remedial assistance for a fee, including aeration and over-excavation (of more than 50 yd3), must be a Certified UST Consultant.
Contaminated soils generated as part of tank removal are to be disposed at the following facility:
Address City State Zip
Contact person Phone
Complete the Facility Site Plat and Sample Information Table on pages 4 and 5 to provide site assessment information.
CONTAMINATION INFORMATION
If contamination at the facility is suspected or confirmed, the information must be reported to the DERR Division Director at (801) 536-
4100 within 24 hours. The Division of Water Quality must be notified at [phone] if Free Product is encountered or if surface water
has been impacted. If contamination is confirmed, any person assisting in the remediation process for a fee must be a Certified UST
Consultant.
SAMPLE INFORMATION TABLE
Complete table for all samples to be taken for closure.
1 Soil (SS), Groundwater (GW), or Unified Soil Classification (USC). 2 Approx. depth in feet below grade. The required minimum site assessment samples must be taken at 0-2 feet below the backfill/native soil interface. 3 Contaminant compounds to be analyzed for each sample (from table on p. 3). 4 Appropriate analysis methods for contaminant compound(s) in each sample (from table on p. 3).
Sample
#
Substance
stored in
tank
Sample
type1 Depth2 Compounds3 Analysis method(s)4
SS-1
SS-2
SS-3
SS-4
SS-5
SS-6
SS-7
SS-8
SS-9
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
GW-1
GW-2
USC-1
USC-2
USC-3
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
Gasoline/Diesel
SS
SS
SS
SS
SS
SS
SS
SS
SS
GW
GW
USC
USC
USC
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
MBTEXN and TPH-GRO & DRO
USC
USC
USC
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
8260/8015
ASTM-D2487
ASTM-D2487
ASTM-D2487
8
8
12-14
12-14
3-5
3-5
12-14
3-5
3-5
3-5
3-5
3-5
3-5
3-5
Intermountain Regional Landfill
800 S Allen Ranch Road Fairfield UT 84013
Bryan Alba [phone]
5
Facility Site Plat (Closure Plan)
The site plat must be drawn to an appropriate identified scale. It must show planned sampling locations, substances stored in tanks, and
other relevant information. Tank and sample identification numbers must be consistent with the information given on pages 1 and 4 of the
Closure Plan.
Facility ID: Drawn By: Date:
X = Sample locations (SS-#, WS-#, USC-#) Site Plat Must Indicate Approximate Locations of:
●= Monitoring Wells (MW-#)-Current & former tanks, piping & dispensers
○= Soil boring (SB-#), or Geoprobe Boring (GP-#)-Location of all samples to be taken
◘= Water Wells (domestic, livestock, etc.)-Buildings, fences, & property boundaries
Slope of Surface Topography: (N,NW,W,SW,S,SE,E,NE)-Utility conduits (sewers, gas, water, storm drains, electrical, etc.)
Land Use At Site: Residential Commercial Industrial
Surrounding Land: _ Residential Commercial Industrial
North Scale: 1”= Feet
6
Approximate depth to groundwater in the vicinity of the tanks: feet.
Regional groundwater flow direction:
State Certified Laboratory to be used:
Address City State Zip
Contact Person Phone
I certify under penalty of law that I am the owner/operator of the tank(s) referenced above and that I am familiar with
the information on this form and that it is true, accurate and complete, and further, that the procedures described herein
will be followed during tank closure.
Signature of tank owner
Full Name of tank owner Date
Please explain any unusual or extenuating circumstances expected regarding the site assessment or closure:
8
North - Northwest
As the depth of backfill was not available from historic records, the depths of soil samples, groundwater samples and USC samples are
approximations, based on sites with similar tanks and GW levels. All depths should be confirmed and/or appropriately adjusted after
field activities determine backfill depth. This site has had at least one historic leak, in 2012, and had 4 steel tanks closed in 2014.
Pace National Analytical
12065 Lebanon Road Mt. Juliet TN 37122
Marty Edwards [phone]
© 2024 Microsoft Corporation © 2024 Maxar ©CNES (2024) Distribution Airbus DS
RUL
CANOPY/DISPENSERS
PUL
DSL
CAR W
A
S
H
SPEEDWAY
Store No. 9414
East Fort Union BLVD
-SIDEWALK-
-CON
C
R
E
T
E
-
OE OE OE OE OE OE OE OE OE OE OE OE OE OE OE OE OE OE
P
PPP
P
P
P
P
P
P P P P
P
P
P
PPP
P
P
P
P
P
P P P P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P P
PP
P
PP
P
The UPS Store
Protein Foundry
Great Clips
ELECTRIC
CONNECTION
BOXES
AIR/VACUUM
DUMPSTER
STORE SIGN
-ASPH
A
L
T
-
-ASPH
A
L
T
-
-ASPH
A
L
T
-
-ASPH
A
L
T
-
CONCRETE
UST AREA
-C
O
N
C
R
E
T
E
-
ELECTRIC CONNECTION BOX
DRAINAGE
GRATE
N
0 20 40
APPROXIMATE SCALE IN FEET
No warranty is made by Stantec as to the accuracy, reliability, or completeness of these data. Original data were compiled from
various sources. This information may not meet National Map Accuracy Standards. This product was developed electronically, and
may be updated without notification. Any reproduction may result in a loss of scale and or information.
FILEPATH:\\us0395-ppfss01\shared_projects\203723864\05_report_deliv\drawings_design\cad_fig\Speedway 9414.dwg|cclee|Apr 17, 2024 at 12:50|Layout: 9414-SM
410 17th Street Suite 1400
Denver, Colorado 80202
LEGEND:
APPROXIMATE PROPERTY BOUNDARY
OVERHEAD ELECTRIC
PRODUCT LINE
POWER POLE
SITE LAMP
P
OE
FOR:
CHECKED BY:DRAWN BY:JOB NUMBER:APPROVED BY:DATE:
FIGURE:
1SITE MAP
TFJMCCL2037XXXXX 4/16/2024
SPEEDWAY No. 9414
1344 FT UNION BLVD
COTTONWOOD HEIGHTS, UTAH 84121
SS-1/USC-1
GW-1 SS-2
GW-2
SS-3SS-4/USC-2
SS-5 SS-6
SS-7
SS-8/USC-3
SS-9