DERR-2024-007689

24-06-05 Subsurface Investigation Report

MAVERIK, INC.
185 S State Street #800
Salt Lake, UT 84111
Phone: [phone]
E-mail: [e-mail]
June 5, 2024

Hillary Mason
Utah Department of Environmental Quality
Division of Environmental Response and Remediation
195 North 1950 West
P.O. Box 144840
Salt Lake City, Utah 84114-4840

RE: 2024 Subsurface Investigation Report
Former Maverik Store #199
1707 S 300 W
Salt Lake City, Utah
Facility ID# 4001356, Release OJQ

Dear Ms. Mason:

Maverik, Inc. (Maverik) is pleased to provide results for the 2024 subsurface investigation performed
at the former Maverik Store #199 site in Salt Lake City, Utah. On May 14, 2024, Earthcore Drilling
Inc. of Salt Lake City, Utah, was hired by Maverik to advance five soil borings and convert those borings
to ground water monitoring wells. New well installation, soil and groundwater sample collection and
handling procedures, and sampling results are discussed in this report.

CONFIRMATION SOIL SAMPLING AND ANALYSIS

Earthcore Drilling advanced the soil borings using a B80 Mobile Drill auger rig according to U.S.
Environmental Protection Agency and Utah Division of Response and Remediation (DERR) protocols.
Mark Stewart, DERR-certified sampler GS-1842, logged the soils encountered and collected soil
samples for laboratory analysis. In general, the soils consisted of up to 5 feet of sandy gravel fill
materials underlain by a poorly graded clay layer (dark brown or gray, generally moist, stiff) down to 15
feet bgs, the maximum depth explored.
Ms. Hillary Mason
June 5, 2024
Page 2
24-06-05 Subsurface Investigation Report
Soil samples were collected in two separate sections using split spoon tooling between approximately
5 and 11 feet below ground surface (bgs). A calibrated MiniRAE 3000 portable VOC monitor with a
photoionization detector (PID) was used to check for hydrocarbon contamination of the soil in the field.
Soil was placed into a plastic bag, sealed, and allowed to warm up. After a few minutes, the sealed
sample container was opened slightly to insert the tip of the VOC monitor to check for the presence of
any hydrocarbon vapors. Field VOC checks with the PID indicated no or negligible soil contamination
as evidenced by very low readings (ranging from 0 ppm to 1.6 ppm) in samples SS-1, SS-3 through
SS-5. No soil samples or PID measurements were taken at SS-2 as this location was entirely within
the recently backfilled former UST tank basin (made up of all clean fill material). In addition to the PID
measurements, there was no identifiable staining or petroleum odor in any soil sample.

A single soil sample was taken from borings SS-1 and S-3 through SS-5 at the location where VOC
measurements were highest or just above the water table and placed into laboratory supplied glass
wide-mouth jars. The jars were put in an iced cooler and transported to Chemtech Ford Analytical
Laboratories of Salt Lake City, Utah for analyses. Soil samples were analyzed for benzene, toluene,
ethylbenzene, total xylenes, naphthalene (BTEXN), methyl tertiary-butyl ether (MTBE), and total
petroleum hydrocarbons-gasoline range organics (TPH-GRO) according to EPA SW-846 Method
8260, and for total petroleum hydrocarbons-diesel range organics (TPH-DRO) according to EPA
Method SW-846 Method 8015. Chain-of-custody protocol was observed.

NEW WELL INSTALLATION

The soil borings were converted to groundwater monitoring wells (identified as MW-1 through MW-5,
see Figure 1). Factory slotted 0.010-inch aperture, 2-inch diameter, schedule 40 PVC well screen was
placed from the bottom of the well (15 ft. bgs) to 5 feet bgs. Blank 2-inch diameter schedule 40 PVC
riser pipe extended from the top of the well screen to within 6 inches of the ground surface. 10-20
grade silica sand was placed in the annular space from bottom of the well to approximately 4.5 ft. bgs.
A hydrated bentonite seal was placed in the annular space from 4.5 ft. bgs to near the surface. The
wells were finished and concreted in place where needed with traffic-rated 8-inch steel well vaults.

Ms. Hillary Mason
June 5, 2024
Page 3
24-06-05 Subsurface Investigation Report
GROUNDWATER SAMPLE COLLECTION AND HANDLING PROCEDURES

Initial groundwater monitoring at the site was conducted on May 15, 2024, by Maverik personnel
according to standard U.S. Environmental Protection Agency and Utah DERR protocols. Mark
Stewart, a Utah certified groundwater and soil sampler (GS-1842), gauged the monitoring wells and
collected groundwater samples for analysis. Groundwater samples were collected from all 5 newly
installed wells.

Groundwater Sampling Protocol
Measure water level depth
Depth to groundwater was measured using a groundwater level probe. The device consisted of a
conductive probe connected to a meter with a calibrated measuring tape. The probe was lowered until
the meter signaled contact with the groundwater surface. Depth to groundwater was measured as the
distance from the top of the well casing to the probe. Measurements were recorded to the nearest
0.01 foot. Please note that the top of casing elevations for the wells were surveyed using a laser level
tying to an arbitrary zero elevation point.

Collect the groundwater sample
The sampled water was collected in laboratory-supplied vials, and the containers were sealed with no
visible air in the vials, i.e., no headspace. The vials were labeled with the sample identification, sample
time and date, and preservative information, and placed into an iced cooler. The sample label
information, the vials size and type, and the number of sample vials were recorded on the Chain-of-
Custody record. A set of 4 40-mL clear vials with 1:1 HCl preservative were used to collect water
samples from each well.

Decontamination
The groundwater level probe was cleaned prior to and between uses. Only dedicated or disposable
equipment were used for groundwater sample collection, requiring no decontamination of sampling
supplies.

Ms. Hillary Mason
June 5, 2024
Page 4
24-06-05 Subsurface Investigation Report
Sample Preparation and Shipment
Groundwater samples from the wells were hand-delivered (within the holding time required for proper
analysis) to Chemtech Ford Analytical Laboratories in Salt Lake City, Utah in an iced cooler. Chain-of-
Custody procedures were followed to track the possession and handling of the samples from collection
to arrival at the laboratory. The Chain-of-Custody included, but was not limited to, project name and
location, client, sampler, sampler signature, sample identification, date and time of sample collection,
sample matrix, container type and number, preservative, analysis requested, and sample handler(s)
and receiver(s) name and signature(s). The Chain-of-Custody records were delivered with the
samples. The samples were checked and logged in by laboratory personnel upon arrival at the
laboratory. Water samples were analyzed for BTEXN, MTBE, TPH-GRO; and TPH-DRO according
to EPA SW-846 8260D and 8015C, respectively.

SOIL AND GROUNDWATER MONITORING RESULTS

Soil Quality Evaluation
All four (4) soil samples were found to be at or below analytical detection limits. Results are
shown in Table 1.

Static Water Level Evaluation
Groundwater depths were measured from the top of casing utilizing the shallowest well, MW-4, as a
baseline (0.00 ft elevation). Water depths measured from the top of casing at each well ranged from
7.25 to 8.64 ft. and water elevation, relative to the baseline, differed by up to 2.24 feet. Groundwater
elevation data indicate a west/southwesterly flow direction at the site for the event. Relative
groundwater elevation data is summarized in Table 2 and relative groundwater elevation contours are
shown on Figure 1.

Groundwater Quality Evaluation
Based on the sampling results, petroleum hydrocarbon contamination, slightly above the Utah Risk
Based Corrective Action Tier 1 Screening Levels (RBCA Tier 1 SLs) exists in MW-2 (TPH-GRO at 16.9
mg/L), a well located within the former tank basin. Samples above Initial Screening levels (ISLs) were
identified in MW-2 (benzene at 0.008 mg/L and TPH-DRO at 9.5 mg/L) and MW-3 (benzene at 0.022
Ms. Hillary Mason
June 5, 2024
Page 5
24-06-05 Subsurface Investigation Report
mg/L). Please note that one duplicate (labeled MW-10, which was a duplicate of MW-1) was analyzed
and the results were within acceptable parameters.

Groundwater analysis results are summarized in Table 2. Analytical reports and Chain-of-Custody
forms are attached.

CONCLUSIONS

Based on the results of recent sampling events, soil conditions around the old tank basin and dispenser
canopy were found to be clean (i.e., no petroleum constituents were identified above laboratory
detection levels). Groundwater was found to be slightly above RBCA Tier 1 SLs for one constituent,
TPH-GRO, and above ISLs for benzene and TPH-GRO in MW-2 (a monitoring well located within the
old tank basin), and above ISLs for benzene in MW-3 (a downgradient well). No other analytes
measured were above their associated screening levels.

From the results, it appears apparent that groundwater contamination is contained onsite and water
quality levels are significantly improving outside of the former UST basin. Maverik plans to conduct
an additional round of groundwater sampling in Quarter 3 of 2024 to determine any groundwater quality
changes over time, unless DERR requests alternate measures or site decisions.

We appreciate your assistance with this site. Please contact me at 801.438.4884 or
[e-mail] should you have any questions.

Sincerely,
Maverik, Inc.

Mark Stewart
Senior Environmental Engineer

Ms. Hillary Mason
June 5, 2024
Page 6
24-06-05 Subsurface Investigation Report
Attachments:

Figure 1 – Well Location and Groundwater Elevation Map
Table 1 – Summary of Soil Quality Data
Table 2 – Summary of Groundwater Quality and Elevation Data

Soil Boring Logs

Laboratory Analysis Reports: Chemtech Ford 24E1212
Chemtech Ford 24E1213

FIGURE 1FORMER MAVERIK STORE #199
SLC, UT
DATE PREPARED: 5/31/2024
MAVERIK, INC
ENVIRONMENTAL DEPARTMENT
185 S STATE ST #800
SALT LAKE CITY, UT 84111
0'15'30'
1" = 30'
N
LEGEND
WATER
SEWER
GAS
ELECTRICAL
Maverik #199
300 WEST
FORMER FUEL CANOPY & DISPENSERS
POWER POLE
17
0
0

S
O
U
T
H
COMMUNICATIONS
1707 S. 300 W.
Salt Lake City, UT
Monitoring Well Locations
MW-1(SS-1)
MW-3 (SS-3)
MW-2
MW-5 (SS-5)
MW-4 (SS-4)
SITE MAP AND SAMPLING
LOCATIONS
FORMER UST BASIN
F
L
O
W
P
A
T
H
0.70'
0.78'
2.24'0.00'
1.99'1.99'Relative Elevation
DATE PID (ppm)
SS-1 05/14/24 1.2 <0.01 <0.04 <0.04 <0.04 <0.04 <0.01 <0.358 <71
SS-2 05/14/24 No samples taken. This location was within the old tank basin and contained clean fill material.
SS-3 05/14/24 1.6 <0.01 <0.03 <0.03 0.03 <0.03 <0.01 <0.322 <72
SS-4 05/14/24 0.3 <0.01 <0.03 <0.03 <0.03 <0.03 <0.01 <0.34 <71
SS-5 05/14/24 0.0 <0.01 <0.04 <0.04 <0.04 <0.04 <0.01 <0.355 <75
Utah ISLs 0.2 9 5 142 51 0.3 150 500
RBCA Tier 1 SLs 0.9 25 23 142 51 0.3 1500 5000
Notes:1. Samples analyzed by Chemtech-Ford Laboratory of Salt Lake City.
2. Bolded values, represent concentrations exceeding Utah Initial Screening Levels (Utah ISLs)
TABLE 1
SUMMARY OF SOIL QUALITY DATA
MAVERIK STORE #199
SLC, UTAH
ANALYTE CONCENTRATIONS (mg/kg)
BENZENE TOLUENE ETHYLBENZENE XYLENES NAPHTHALENE MTBE TPH-GRO TPH-DRO
WELL DATE
IDENTIFICATION
5/15/2024 0.70 <0.005 <0.012 <0.012 <0.012 <0.012 <0.005 <0.125 <1.0
5/15/2024 0.78 0.008 0.045 0.251 5.18 0.281 <0.005 16.9 9.5
5/15/2024 2.24 0.022 <0.012 <0.012 0.043 <0.012 <0.005 0.193 <1.0
5/15/2024 0.00 <0.005 <0.012 <0.012 <0.012 <0.012 <0.005 <0.125 <1.0
MW-5 5/15/2024 1.99 <0.005 <0.012 <0.012 <0.012 <0.012 <0.005 <0.125 <1.0
Utah ISLs 0.005 1 0.7 10 0.7 0.2 1 1
RBCA Tier 1 SLs 0.3 3 4 10 0.7 0.2 10 10
Notes:1. Samples analyzed by Chemtech-Ford Laboratory of Salt Lake City.
2. Bolded values, represent concentrations exceeding Utah Initial Screening Levels (Utah ISLs)
3. Highlighted values, if any, represent concentrations exceeding the RBCA Tier 1 Screening Levels (RBCA Tier 1 SLs)
SUMMARY OF GROUNDWATER QUALITY AND ELEVATION DATA
TABLE 2
ANALYTE CONCENTRATIONS (mg/L)
BENZENE TOLUENE ETHYLBENZENE NAPHTHALENE MTBE TPH-GRO TPH-DRO
SLC, UTAH
MAVERIK STORE #199
MW-1
MW-2
MW-3
MW-4
XYLENES
RELATIVE
ELEVATION
(ft.)

SOIL BORING LOGS

05/2013 cmz DNR Form 542-1392
Soil Boring Log And Monitoring Well Construction Diagram for:
Facility Name: UST Registration No.: LUST No.:
Well Contractor Name: Drilling Method**:
Well Contractor Registration Number: Boring Depth (ft) x Diameter (in):
Logged by: Ground Surface Elevation (ASL):
Start Date: Finish Date: Top of Casing Elevation (ASL):
Depth
(feet)Well Construction Details
Sample PID / FID
PPM

USCS Sample Descriptions: soil, color,
classification, observation
Example: Silty clay, dark gray, hard, moist, strong odor No. Type*

* Sample Types:
Split Spoon (SS)
Continuous Core (CC)
** Drilling Method Options:
Rotary Auger, Push Probe, Hand Auger, Air drilling, Hollow
Stem Auger, Other (Describe)
Symbols to Use:
v Static Water Level
s sample collected
Observation Date:
Time
Static Water Level (ASL)
05/2013 cmz DNR Form 542-1392
Soil Boring Log And Monitoring Well Construction Diagram for:
Facility Name: UST Registration No.: LUST No.:
Well Contractor Name: Drilling Method**:
Well Contractor Registration Number: Boring Depth (ft) x Diameter (in):
Logged by: Ground Surface Elevation (ASL):
Start Date: Finish Date: Top of Casing Elevation (ASL):
Depth
(feet)Well Construction Details
Sample PID / FID
PPM

USCS Sample Descriptions: soil, color,
classification, observation
Example: Silty clay, dark gray, hard, moist, strong odor No. Type*

* Sample Types:
Split Spoon (SS)
Continuous Core (CC)
** Drilling Method Options:
Rotary Auger, Push Probe, Hand Auger, Air drilling, Hollow
Stem Auger, Other (Describe)
Symbols to Use:
v Static Water Level
s sample collected
Observation Date:
Time
Static Water Level (ASL)
05/2013 cmz DNR Form 542-1392
Soil Boring Log And Monitoring Well Construction Diagram for:
Facility Name: UST Registration No.: LUST No.:
Well Contractor Name: Drilling Method**:
Well Contractor Registration Number: Boring Depth (ft) x Diameter (in):
Logged by: Ground Surface Elevation (ASL):
Start Date: Finish Date: Top of Casing Elevation (ASL):
Depth
(feet)Well Construction Details
Sample PID / FID
PPM

USCS Sample Descriptions: soil, color,
classification, observation
Example: Silty clay, dark gray, hard, moist, strong odor No. Type*

* Sample Types:
Split Spoon (SS)
Continuous Core (CC)
** Drilling Method Options:
Rotary Auger, Push Probe, Hand Auger, Air drilling, Hollow
Stem Auger, Other (Describe)
Symbols to Use:
v Static Water Level
s sample collected
Observation Date:
Time
Static Water Level (ASL)
05/2013 cmz DNR Form 542-1392
Soil Boring Log And Monitoring Well Construction Diagram for:
Facility Name: UST Registration No.: LUST No.:
Well Contractor Name: Drilling Method**:
Well Contractor Registration Number: Boring Depth (ft) x Diameter (in):
Logged by: Ground Surface Elevation (ASL):
Start Date: Finish Date: Top of Casing Elevation (ASL):
Depth
(feet)Well Construction Details
Sample PID / FID
PPM

USCS Sample Descriptions: soil, color,
classification, observation
Example: Silty clay, dark gray, hard, moist, strong odor No. Type*

* Sample Types:
Split Spoon (SS)
Continuous Core (CC)
** Drilling Method Options:
Rotary Auger, Push Probe, Hand Auger, Air drilling, Hollow
Stem Auger, Other (Describe)
Symbols to Use:
v Static Water Level
s sample collected
Observation Date:
Time
Static Water Level (ASL)

Laboratory Analysis Reports:
Chemtech Ford 24E1212 (Soil Data)
Chemtech Ford 24E1213 (Groundwater Data)

The analyses presented on this report were performed in accordance with the
National Environmental Laboratory Accreditation Program (NELAP) unless
noted in the comments, flags, or case narrative. If the report is to be used for
regulatory compliance, it should be presented in its entirety, and not be
altered.
Client Service Contact: 801.262.7299
Maverik, Inc.
Attn: Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
Work Order: 24E1212
Project: SLC 199
5/24/2024
Approved By:
Reed Hendricks, Lab Director
9632 South 500 West Sandy, Utah 84070
Serving the Intermountain West since 1953
801.262.7299 Main 866.792.0093 Fax www.ChemtechFord.com
Page 1 of 12
_____________________________________________________________________________________________
Maverik, Inc.
Project: SLC 199
Project Manager: Mark Stewart
Laboratory ID Sample Name
24E1212-01 SS - 1
24E1212-02 SS - 3
24E1212-03 SS - 4
24E1212-04 SS - 5
______________________________________________________________________________________________
Work Order Report Narrative
Sample Preparation
All samples were prepared within method specified holding times. No preparation issues were noted.
Method Blanks
All blank values were within method acceptance criteria. No blank values exceeded the minimum reporting limit for any
analysis in this work order.
Laboratory Control Samples
All laboratory control samples were within method acceptance criteria.
Method Spikes
All method spike recoveries were within method acceptance criteria, except as noted by qualifying flags.
Method Spike Duplicates
All method spike duplicates were within method acceptance criteria, except as noted by qualifying flags.
Corrective Actions
There are no corrective actions associated with this work order.
www.ChemtechFord.com
Project Name: SLC 199 CtF WO#: 24E1212
Page 2 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/24/2024
SLC 199
Sample ID: SS - 1
Lab ID: 24E1212-01Matrix: Solid
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/14/24 15:30
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
Inorganic
%5/17/245/16/240.1 CTF800070.6Total Solids
MBTEXn
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDBenzene
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDEthylbenzene
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDNaphthalene
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDToluene
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/kg dry 5/20/245/20/240.358 EPA 8260B/C 5035A/[CALC]NDGasoline Range Organics
Diesel Range
mg/kg dry 5/20/245/17/2471EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1212
www.ChemtechFord.com
Page 3 of 12Page 3 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/24/2024
SLC 199
Sample ID: SS - 3
Lab ID: 24E1212-02Matrix: Solid
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/14/24 13:40
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
Inorganic
%5/17/245/16/240.1 CTF800069.9Total Solids
MBTEXn
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDBenzene
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDEthylbenzene
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDNaphthalene
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDToluene
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030B0.03Xylenes, total
Gasoline Range
mg/kg dry 5/20/245/20/240.322 EPA 8260B/C 5035A/[CALC]NDGasoline Range Organics
Diesel Range
mg/kg dry 5/20/245/17/2472EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1212
www.ChemtechFord.com
Page 4 of 12Page 4 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/24/2024
SLC 199
Sample ID: SS - 4
Lab ID: 24E1212-03Matrix: Solid
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/14/24 12:30
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
Inorganic
%5/17/245/16/240.1 CTF800070.7Total Solids
MBTEXn
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDBenzene
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDEthylbenzene
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDNaphthalene
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDToluene
mg/kg dry 5/20/245/20/240.03 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/kg dry 5/20/245/20/240.340 EPA 8260B/C 5035A/[CALC]NDGasoline Range Organics
Diesel Range
mg/kg dry 5/20/245/17/2471EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1212
www.ChemtechFord.com
Page 5 of 12Page 5 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/24/2024
SLC 199
Sample ID: SS - 5
Lab ID: 24E1212-04Matrix: Solid
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/14/24 11:40
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
Inorganic
%5/17/245/16/240.1 CTF800066.4Total Solids
MBTEXn
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDBenzene
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDEthylbenzene
mg/kg dry 5/20/245/20/240.01 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDNaphthalene
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDToluene
mg/kg dry 5/20/245/20/240.04 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/kg dry 5/20/245/20/240.355 EPA 8260B/C 5035A/[CALC]NDGasoline Range Organics
Diesel Range
mg/kg dry 5/20/245/17/2475EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1212
www.ChemtechFord.com
Page 6 of 12Page 6 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/24/2024
SLC 199
Report Footnotes
Abbreviations
ND = Not detected at the corresponding Minimum Reporting Limit (MRL).
1 mg/L = one milligram per liter or 1 mg/kg = one milligram per kilogram = 1 part per million.
1 ug/L = one microgram per liter or 1 ug/kg = one microgram per kilogram = 1 part per billion.
1 ng/L = one nanogram per liter or 1 ng/kg = one nanogram per kilogram = 1 part per trillion.
On calculated parameters, there may be a slight difference between summing the rounded values shown on the report
vs the unrounded values used in the calculation.
Project Name: SLC 199 CtF WO#: 24E1212
www.ChemtechFord.com
Page 7 of 12Page 7 of 12
Page 8 of 12
QC Report for Work Order (WO) - 24E1212
% Rec RPD RPD Max MRL DFResultSpk ValueLimitsSource ConcAnalyte
Duplicate - CTF8000
QC Sample ID: BYE0831-DUP1 QC Source Sample: 24E1212-01Batch: BYE0831
Date Prepared: 05/16/2024 Date Analyzed: 05/17/2024
Total Solids 1.16 20 71.4 70.6 0.1 1.00
CtF WO#: 24E1212
www.ChemtechFord.com Page 9 of 12
QC Report for Work Order (WO) - 24E1212
% Rec RPD RPD Max MRL DFResultSpk ValueLimitsSource ConcAnalyte
Blank - EPA 8015 C
QC Sample ID: BYE0918-BLK1 Batch: BYE0918
Date Prepared: 05/17/2024 Date Analyzed: 05/20/2024
Diesel Range Organics ND 50 1.00
LCS - EPA 8015 C
QC Sample ID: BYE0918-BS1 Batch: BYE0918
Date Prepared: 05/17/2024 Date Analyzed: 05/20/2024
Diesel Range Organics 104 50 - 150 2070 2000 50 1.00
Matrix Spike - EPA 8015 C
QC Sample ID: BYE0918-MS1 QC Source Sample: 24E1212-01Batch: BYE0918
Date Prepared: 05/17/2024 Date Analyzed: 05/20/2024
Diesel Range Organics 104 50 - 150 2930 ND 2830 71 1.00
Matrix Spike Dup - EPA 8015 C
QC Sample ID: BYE0918-MSD1 QC Source Sample: 24E1212-01Batch: BYE0918
Date Prepared: 05/17/2024 Date Analyzed: 05/20/2024
Diesel Range Organics 101 3.02 50 - 150 20 2850 ND 2830 71 1.00
CtF WO#: 24E1212
www.ChemtechFord.com Page 10 of 12
QC Report for Work Order (WO) - 24E1212
% Rec RPD RPD Max MRL DFResultSpk ValueLimitsSource ConcAnalyte
Blank - EPA 8260D
QC Sample ID: BYE0978-BLK1 Batch: BYE0978
Date Prepared: 05/20/2024 Date Analyzed: 05/20/2024
Benzene ND 0.0004 1.00
Ethylbenzene ND 0.001 1.00
Methyl tert-Butyl Ether (MTBE)ND 0.0004 1.00
Naphthalene ND 0.001 1.00
Toluene ND 0.001 1.00
Xylenes, total ND 0.001 1.00
LCS - EPA 8260D
QC Sample ID: BYE0978-BS1 Batch: BYE0978
Date Prepared: 05/20/2024 Date Analyzed: 05/20/2024
Benzene 77.4 70 - 130 0.008 0.0100 0.0004 1.00
Ethylbenzene 92.1 70 - 130 0.009 0.0100 0.001 1.00
Methyl tert-Butyl Ether (MTBE)91.5 70 - 130 0.009 0.0100 0.0004 1.00
Naphthalene 93.5 70 - 130 0.009 0.0100 0.001 1.00
Toluene 87.6 70 - 130 0.009 0.0100 0.001 1.00
Xylenes, total 99.7 70 - 130 0.03 0.0300 0.001 1.00
Matrix Spike - EPA 8260D
QC Sample ID: BYE0978-MS1 QC Source Sample: 24E1212-01Batch: BYE0978
Date Prepared: 05/20/2024 Date Analyzed: 05/20/2024
Benzene 72.4 70 - 130 0.25 ND 0.344 0.01 1.00
Ethylbenzene 85.9 50 - 150 0.30 ND 0.344 0.03 1.00
Methyl tert-Butyl Ether (MTBE)93.2 50 - 150 0.32 ND 0.344 0.01 1.00
Naphthalene 88.4 50 - 150 0.30 ND 0.344 0.03 1.00
Toluene 77.3 70 - 130 0.27 ND 0.344 0.03 1.00
Xylenes, total 86.9 70 - 130 0.90 ND 1.03 0.03 1.00
Matrix Spike Dup - EPA 8260D
QC Sample ID: BYE0978-MSD1 QC Source Sample: 24E1212-01Batch: BYE0978
Date Prepared: 05/20/2024 Date Analyzed: 05/20/2024
Benzene 70.3 5.81 70 - 130 20 0.23 ND 0.334 0.01 1.00
Ethylbenzene 73.5 18.4 50 - 150 25 0.25 ND 0.334 0.03 1.00
Methyl tert-Butyl Ether (MTBE)93.2 2.87 50 - 150 25 0.31 ND 0.334 0.01 1.00
Naphthalene 86.1 5.51 50 - 150 25 0.29 ND 0.334 0.03 1.00
Toluene 80.0 0.562 70 - 130 20 0.27 ND 0.334 0.03 1.00
Xylenes, total 82.6 7.90 70 - 130 20 0.83 ND 1.00 0.03 1.00
CtF WO#: 24E1212
www.ChemtechFord.com Page 11 of 12
Surrogates Report for Work Order (WO) - 24E1212
Spk ValueResultUCL DF BatchLCL% RecAnalyteQC ID
Blank - EPA 8015 C
BYE0918-BLK1 Bromofluorobenzene 94.4 50 BYE0918 1.00150 189 200
LCS - EPA 8015 C
BYE0918-BS1 Bromofluorobenzene 98.5 50 BYE0918 1.00150 197 200
Matrix Spike - EPA 8015 C
BYE0918-MS1 Bromofluorobenzene 92.6 50 BYE0918 1.00150 262 283
Matrix Spike Dup - EPA 8015 C
BYE0918-MSD1 Bromofluorobenzene 93.1 50 BYE0918 1.00150 264 283
Blank - EPA 8260D
BYE0978-BLK1 Toluene-d8 99.6 82 BYE0978 1.001260.00996 0.0100
LCS - EPA 8260D
BYE0978-BS1 Toluene-d8 99.5 82 BYE0978 1.001260.00995 0.0100
Matrix Spike - EPA 8260D
BYE0978-MS1 Toluene-d8 97.9 82 BYE0978 1.001260.337 0.344
Matrix Spike Dup - EPA 8260D
BYE0978-MSD1 Toluene-d8 100 82 BYE0978 1.001260.335 0.334
UCLLCL%RecResultAnalyteLabNumber
Surrogate Recoveries (Field Samples)
SpkLvl Qualifier
DRO
24E1212-01 Bromofluorobenzene 190 67.2 50 150283
MBTEXN-GRO
24E1212-01 Toluene-d8 0.357 99.8 82 1260.358
DRO
24E1212-02 Bromofluorobenzene 163 56.8 50 150286
MBTEXN-GRO
24E1212-02 Toluene-d8 0.320 99.2 82 1260.322
DRO
24E1212-03 Bromofluorobenzene 170 60.3 50 150283
MBTEXN-GRO
24E1212-03 Toluene-d8 0.339 99.7 82 1260.340
DRO
24E1212-04 Bromofluorobenzene 222 73.6 50 150301
MBTEXN-GRO
24E1212-04 Toluene-d8 0.350 98.5 82 1260.355
CtF WO#: 24E1212
www.ChemtechFord.com Page 12 of 12
The analyses presented on this report were performed in accordance with the
National Environmental Laboratory Accreditation Program (NELAP) unless
noted in the comments, flags, or case narrative. If the report is to be used for
regulatory compliance, it should be presented in its entirety, and not be
altered.
Client Service Contact: 801.262.7299
Maverik, Inc.
Attn: Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
Work Order: 24E1213
Project: SLC 199
5/28/2024
Approved By:
Reed Hendricks, Lab Director
9632 South 500 West Sandy, Utah 84070
Serving the Intermountain West since 1953
801.262.7299 Main 866.792.0093 Fax www.ChemtechFord.com
Page 1 of 12
_____________________________________________________________________________________________
Maverik, Inc.
Project: SLC 199
Project Manager: Mark Stewart
Laboratory ID Sample Name
24E1213-01 MW - 1
24E1213-02 MW - 2
24E1213-03 MW - 3
24E1213-04 MW - 4
24E1213-05 MW - 5
24E1213-06 MW - 10
______________________________________________________________________________________________
Work Order Report Narrative
Sample Preparation
All samples were prepared within method specified holding times. No preparation issues were noted.
Method Blanks
All blank values were within method acceptance criteria. No blank values exceeded the minimum reporting limit for any
analysis in this work order.
Laboratory Control Samples
All laboratory control samples were within method acceptance criteria.
Method Spikes
All method spike recoveries were within method acceptance criteria, except as noted by qualifying flags.
Method Spike Duplicates
All method spike duplicates were within method acceptance criteria, except as noted by qualifying flags.
Corrective Actions
There are no corrective actions associated with this work order.
www.ChemtechFord.com
Project Name: SLC 199 CtF WO#: 24E1213
Page 2 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Sample ID: MW - 1
Lab ID: 24E1213-01Matrix: Water
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/15/24 15:15
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
MBTEXn
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDBenzene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDEthylbenzene
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDNaphthalene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDToluene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/L 5/16/245/16/240.125 EPA 8260B/C /5030A/[CALC]NDGasoline Range Organics
Diesel Range
mg/L 5/23/245/23/241.0 EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 3 of 12Page 3 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Sample ID: MW - 2
Lab ID: 24E1213-02Matrix: Water
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/15/24 16:00
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
MBTEXn
mg/L 5/16/245/16/240.005 EPA 8260D/5030B0.008Benzene
mg/L 5/16/245/16/240.012 EPA 8260D/5030B0.251Ethylbenzene
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/L 5/16/245/16/240.012 EPA 8260D/5030B0.281Naphthalene
mg/L 5/16/245/16/240.012 EPA 8260D/5030B0.045Toluene
mg/L 5/16/245/16/240.250 EPA 8260D/5030B5.18Xylenes, total
Gasoline Range
mg/L 5/16/245/16/240.250 EPA 8260B/C /5030A/[CALC]16.9Gasoline Range Organics
Diesel Range
mg/L 5/23/245/23/241.0 EPA 8015 C9.5Diesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 4 of 12Page 4 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Sample ID: MW - 3
Lab ID: 24E1213-03Matrix: Water
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/15/24 15:35
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
MBTEXn
mg/L 5/16/245/16/240.005 EPA 8260D/5030B0.022Benzene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDEthylbenzene
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDNaphthalene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDToluene
mg/L 5/16/245/16/240.012 EPA 8260D/5030B0.043Xylenes, total
Gasoline Range
mg/L 5/16/245/16/240.125 EPA 8260B/C /5030A/[CALC]0.193Gasoline Range Organics
Diesel Range
mg/L 5/23/245/23/241.0 EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 5 of 12Page 5 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Sample ID: MW - 4
Lab ID: 24E1213-04Matrix: Water
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/15/24 15:50
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
MBTEXn
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDBenzene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDEthylbenzene
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDNaphthalene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDToluene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/L 5/16/245/16/240.125 EPA 8260B/C /5030A/[CALC]NDGasoline Range Organics
Diesel Range
mg/L 5/23/245/23/241.0 EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 6 of 12Page 6 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Sample ID: MW - 5
Lab ID: 24E1213-05Matrix: Water
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/15/24 16:10
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
MBTEXn
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDBenzene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDEthylbenzene
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDNaphthalene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDToluene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/L 5/16/245/16/240.125 EPA 8260B/C /5030A/[CALC]NDGasoline Range Organics
Diesel Range
mg/L 5/23/245/23/241.0 EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 7 of 12Page 7 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Sample ID: MW - 10
Lab ID: 24E1213-06Matrix: Water
Flag(s)Units
Analysis
Date/Time
Date Sampled: 5/15/24 16:15
Preparation
Date/Time
Sampled By: Mark Stewart
Minimum
Reporting
Limit MethodResult
MBTEXn
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDBenzene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDEthylbenzene
mg/L 5/16/245/16/240.005 EPA 8260D/5030BNDMethyl tert-Butyl Ether (MTBE)
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDNaphthalene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDToluene
mg/L 5/16/245/16/240.012 EPA 8260D/5030BNDXylenes, total
Gasoline Range
mg/L 5/16/245/16/240.125 EPA 8260B/C /5030A/[CALC]NDGasoline Range Organics
Diesel Range
mg/L 5/23/245/23/241.0 EPA 8015 CNDDiesel Range Organics
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 8 of 12Page 8 of 12
xx
Chemtech-Ford Laboratories
Serving the Intermountain West Since 1953
Certificate of Analysis
9632 South 500 West
Sandy, UT 84070
O:[phone] F: [phone]
www.ChemtechFord.com
Maverik, Inc.
Mark Stewart
185 S State Street Suite 800
Salt Lake City, UT 84111
PO#:
Receipt:
Date Reported:
Project Name:
01-199-7080-11
5/16/24 8:14 @ 3.1 °C
5/28/2024
SLC 199
Report Footnotes
Abbreviations
ND = Not detected at the corresponding Minimum Reporting Limit (MRL).
1 mg/L = one milligram per liter or 1 mg/kg = one milligram per kilogram = 1 part per million.
1 ug/L = one microgram per liter or 1 ug/kg = one microgram per kilogram = 1 part per billion.
1 ng/L = one nanogram per liter or 1 ng/kg = one nanogram per kilogram = 1 part per trillion.
On calculated parameters, there may be a slight difference between summing the rounded values shown on the report
vs the unrounded values used in the calculation.
Project Name: SLC 199 CtF WO#: 24E1213
www.ChemtechFord.com
Page 9 of 12Page 9 of 12
Page 10 of 12
QC Report for Work Order (WO) - 24E1213
% Rec RPD RPD Max MRL DFResultSpk ValueLimitsSource ConcAnalyte
Blank - EPA 8015 C
QC Sample ID: BYE1192-BLK1 Batch: BYE1192
Date Prepared: 05/23/2024 Date Analyzed: 05/23/2024
Diesel Range Organics ND 1.0 1.00
LCS - EPA 8015 C
QC Sample ID: BYE1192-BS1 Batch: BYE1192
Date Prepared: 05/23/2024 Date Analyzed: 05/23/2024
Diesel Range Organics 108 50 - 150 43 40.0 1.0 1.00
Matrix Spike - EPA 8015 C
QC Sample ID: BYE1192-MS1 QC Source Sample: 24E1213-01Batch: BYE1192
Date Prepared: 05/23/2024 Date Analyzed: 05/23/2024
Diesel Range Organics 108 50 - 150 43 ND 40.0 1.0 1.00
Matrix Spike Dup - EPA 8015 C
QC Sample ID: BYE1192-MSD1 QC Source Sample: 24E1213-01Batch: BYE1192
Date Prepared: 05/23/2024 Date Analyzed: 05/23/2024
Diesel Range Organics 115 6.31 50 - 150 20 46 ND 40.0 1.0 1.00
CtF WO#: 24E1213
www.ChemtechFord.com Page 11 of 12
QC Report for Work Order (WO) - 24E1213
% Rec RPD RPD Max MRL DFResultSpk ValueLimitsSource ConcAnalyte
Blank - EPA 8260D
QC Sample ID: BYE0851-BLK1 Batch: BYE0851
Date Prepared: 05/16/2024 Date Analyzed: 05/16/2024
Benzene ND 0.0004 1.00
Ethylbenzene ND 0.001 1.00
Methyl tert-Butyl Ether (MTBE)ND 0.0004 1.00
Naphthalene ND 0.001 1.00
Toluene ND 0.001 1.00
Xylenes, total ND 0.001 1.00
LCS - EPA 8260D
QC Sample ID: BYE0851-BS1 Batch: BYE0851
Date Prepared: 05/16/2024 Date Analyzed: 05/16/2024
Benzene 89.9 70 - 130 0.009 0.0100 0.0004 1.00
Ethylbenzene 106 70 - 130 0.011 0.0100 0.001 1.00
Methyl tert-Butyl Ether (MTBE)94.6 70 - 130 0.009 0.0100 0.0004 1.00
Naphthalene 106 70 - 130 0.011 0.0100 0.001 1.00
Toluene 105 70 - 130 0.010 0.0100 0.001 1.00
Xylenes, total 106 70 - 130 0.032 0.0300 0.001 1.00
Matrix Spike - EPA 8260D
QC Sample ID: BYE0851-MS1 QC Source Sample: 24E1213-01Batch: BYE0851
Date Prepared: 05/16/2024 Date Analyzed: 05/16/2024
Benzene 79.8 70 - 130 0.100 ND 0.125 0.005 1.00
Ethylbenzene 95.5 70 - 130 0.119 ND 0.125 0.012 1.00
Methyl tert-Butyl Ether (MTBE)74.6 70 - 130 0.093 ND 0.125 0.005 1.00
Naphthalene 97.3 70 - 130 0.122 ND 0.125 0.012 1.00
Toluene 88.8 70 - 130 0.111 ND 0.125 0.012 1.00
Xylenes, total 97.0 70 - 130 0.364 ND 0.375 0.012 1.00
Matrix Spike Dup - EPA 8260D
QC Sample ID: BYE0851-MSD1 QC Source Sample: 24E1213-01Batch: BYE0851
Date Prepared: 05/16/2024 Date Analyzed: 05/16/2024
Benzene 81.1 1.62 70 - 130 20 0.101 ND 0.125 0.005 1.00
Ethylbenzene 99.4 4.00 70 - 130 25 0.124 ND 0.125 0.012 1.00
Methyl tert-Butyl Ether (MTBE)84.8 12.8 70 - 130 25 0.106 ND 0.125 0.005 1.00
Naphthalene 104 6.56 70 - 130 25 0.130 ND 0.125 0.012 1.00
Toluene 93.7 5.37 70 - 130 20 0.117 ND 0.125 0.012 1.00
Xylenes, total 97.7 0.719 70 - 130 20 0.366 ND 0.375 0.012 1.00
CtF WO#: 24E1213
www.ChemtechFord.com Page 12 of 12