DAQ-2024-004375

1

DAQC-012-24
Site ID’s: 100546, 100742 (B4)

MEMORANDUM

TO: STACK TEST FILE – OVINTIV USA INC. – Deveraux 1-14-4-1 Well Pad and
Amy UT 13-7 3-1 – Duchesne County

THROUGH: Rik Ombach, Minor Source Oil & Gas Compliance Section Manager

FROM: Kyle Greenberg, Environmental Scientist

DATE: January 4, 2024

SUBJECT: Source: Deveraux 1-14-4-1 Well Pad: Doosan 11.1L; SN: EEIOH404226
Amy UT 13-7 3-1: Doosan 14.6L; SN: EEZOG401147
Location: Duchesne County, Utah
Contact: Ryan Zillner: 720-876-3144
Tester: Great Plains Analytical Services, Inc.
Site ID #: 100546, 100742
Permit/AO #: Permit by Rule
Subject: Review of Pretest Protocol dated September 28, 2023

On January 3, 2024, Utah Division of Air Quality (DAQ) received protocols for testing of one (1) Doosan
11.1L at Deveraux 1-14-4-1 Well Pad and one (1) Doosan 14.6L at Amy UT 13-7 3-1 in Duchesne
County, Utah. Testing will be performed the week of February 5, 2024, to determine compliance with the
emission limits found in Utah Administrative Code R307-510 and 40 CFR Part 60 Subpart JJJJ.

PROTOCOL CONDITIONS:

1. RM 1 used to determine sample velocity traverses; OK
2. RM 2 used to determine stack gas velocity and volumetric flow rate; OK
3. RM 3A used to determine dry molecular weight of the gas stream; OK
4. ASTM D6348-03 used to determine H2O content; NOx, CO, and VOC emissions; OK
DEVIATIONS: None.

CONCLUSION: The protocol appears to be acceptable.

RECOMMENDATION: The methods proposed in the protocol are capable of determining
compliance with the unit’s emission limits, it is recommended the pretest
protocol be determined as acceptable.

ATTACHMENTS: Ovintiv pretest protocol and notice of testing date.

01/03/2024
VIA Stack Test Report Submission:
https://utahgov.co1.qualtrics.com/jfe/form/SV_3dSxf7JSzy4jwGh
Rik Ombach
Manager, Minor Source Compliance
Utah Department of Environmental Quality
Division of Air Quality
195 North 1950 West
Salt Lake City, Utah 84116
RE: Notification of Performance Testing
Ovintiv USA Inc.
Duchesne County
Dear Mr. Ombach:
Ovintiv USA Inc. is providing notification of performance testing for the spark ignition internal combustion
engines that satisfy the following requirements for which the engines are subject:
•40 CFR Part 60 Subpart JJJJ: 40 CFR §60.8 and §60.4243(b)(2)(i) initial test or
§60.4243(b)(2)(ii) initial test or subsequent test every 8,760 hours or 3 years, whichever
comes first; and
•Permit by Rule
Performance testing has been scheduled for the week of February 5, 2024.
Facility Latitude/
Longitude
CAERS
Source ID
Unit ID Manufacturer
& Model
Serial
Number
Deveraux 1-14-4-1 40.141583,
-109.957685
100546 11-17-015 Doosan 11.1L EEIOH404226
The performance testing protocol is attached. If you have any questions, please contact me at 720-876-
3144 or [e-mail].
Sincerely,
Ryan Zillner
Senior Air Quality Engineer
Attachment
Great Plains Analytical Services, Inc.
Performance Test Protocol
40 CFR Part 60 Subpart JJJJ
Prepared by
303 West 3rd StreetElk City, OK 73644

!#"8'#": %( 7"<'.$ %$
16.7'.6 8(9 :7;<
Great Plains Analytical Services, Inc.
1.0 Introduction………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
1.1 Contact Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
2.0 Test Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
3.0 Method Synopsis………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….5
4.0 Emission Point Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
4.1 Target Analytes………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
4.2 Test Quality Objectives………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
5.0 Quality Control Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….7
6.0 Additional Information and Reporting………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….8
7.0 Example Calculations………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….8
8.0 Health and Safety Concerns………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….9
1.1 Contact Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
2.0 Source Information and Testing Dates………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
2.1 Testing Limits and Parameters (Federal)………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….4
2.2 Testing Limits and Parameters (State)………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….4
2.3 Additional Parameters………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….4
4.2 Test Specific Target Analytes and Data Quality Objectives………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
5.0 QA/QC………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….7
5.1 Measurement System Capabilities………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….7
3.1 Sample Port Location………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….5
3.2 Sample locations inside the stack………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….5
9.0 Sampling Schematic Diagram………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….9
10.0 Engine Parameter Data Sheet Diagram………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….10
11.0 Velocity Field Data Diagram………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….10
Table of Contents
Table(s)
Figure(s)
Protocol Attachment(s)
3
Great Plains Analytical Services, Inc.
2.0 Test Information (continued)
1.0 Introduction
Tests will consist of (3) 60 minute test runs.
The test will be conducted using a multi component gas analyzer that incorporates a Fourier Transform Infrared (FTIR) spectrometer. FTIR is state of the art technology. It is
designed to military specifications and allows simple calibration using only single component calibration gases.
370 17th Street, Suite 1700 Denver CO 80202
370 17th Street, Suite 1700 Denver CO 80202
4 Waterway Square Place, Suite 100 The Woodlands, TX
77380
Ovintiv USA Inc 720-876-3144 [e-mail]
Ovintiv USA Inc 281-847-6093 [e-mail]
1.1 Contact Information
2.0 Test Information
Date of
ManufactureTest Dates
[e-mail]
Ovintiv USA Inc.720-876-3017 [e-mail]
Table 2.0 Test Information and Testing Dates
GAS has been contracted by Ovintiv USA Inc. to conduct source testing services at located in County, . The purpose of this test plan is to document the test methods and procedures
that will be employed to collect and analyze exhaust gas emissions during performance testing of the internal combustion engines fueled by Natural Gas.
Contact
Macie McClellan
Physical Address
303 W 3rd St. Elk City, OK 73644GAS580-225-0403
Ryan Zillner
Brandon Lithgoe
Table 1.1 Contact Information
Thien Nguyen
Serial Number Location/Facility
Name Make and Model Horsepower RN#
Application Telephone Email Address
Source ID Engine
Classification
4
Great Plains Analytical Services, Inc.
g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2
g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2
3A
D6348-03
1/1A
% H2O
Sample Location Inches (")
CO2, H2O, NOx, CO, VOC, and CH2O will be
measured using a Gasmet multigas FTIR analyzer in
accordance with ASTM Method D6348 when
applicable analytes are being tested for.
Footnote
Table 2.3 Additional Parameters
Reduction %
Reference Method 10/2
COOxygen (O2)%vd
Moisture
CH2O
320
Reduction %
Table 2.4 Testing Limits and Parameters (Reduction)
Source ID
Table 2.2 Testing Limits and Parameters (State)
Source ID
NOx CO VOC (NMNEHC)CH2O
Reference Method ASTM D6348-03 Reference Method ASTM D6348-03 Reference Method ASTM D6348-03 Reference Method ASTM D6348-03
CH2O
Reference Method ASTM D6348-03Reference Method ASTM D6348-03Reference Method ASTM D6348-03
Table 2.1 Testing Limits and Parameters (Federal)
Reference Method ASTM D6348-03Source ID
VOC (NMNEHC)NOx CO
5
Great Plains Analytical Services, Inc.
3.0 Method Synopsis
EPA Method 1
Figure 3.1
Figure 3.2
The purpose of the method is to provide guidance for the selection of sampling ports and traverse points at which sampling for air pollutants will be
performed pursuant to regulations set forth in this part. Method 1 may be modified as allowed in Subpart JJJJ & ZZZZ. Alternatively, for NOx, CO,
VOC, O2, and moisture measurement, ducts ≤6 inches in diameter may be sampled at a single point located at the duct centroid and ducts >6 and
≤12 inches in diameter may be sampled at 3 traverse points located at 16.7, 50.0, and 83.3% of the measurement line ('3-point long line'). If the
duct is >12 inches in diameter and the sampling port location meets the two and half-diameter criterion of Section 11.1.1 of Method 1 of 40 CFR
part 60, Appendix A, the duct may be sampled at '3-point long line'; otherwise, conduct the stratification testing and select sampling points
according to Section 8.1.2 of Method 7E of 40 CFR part 60, Appendix A."
For all stacks greater than 6" in diameter, GAS will use a sampling port that is located at a minimum of 2 stack diameters downstream from any
disturbance, and 1/2 stack diameter upstream from any disturbance.
For all stacks greater than 6" in diameter, GAS will sample at 3 points within the stack. These points will be located at 83.3%, 50%, and 16.7% of the
stack diameter.
1/2 diameter upstream
2 diameters downstream
Figure 3.2. Sample locations inside the stack
Actual diameter
Figure 3.1. Sample Port Location
6
Great Plains Analytical Services, Inc.
4.1 Target Analytes
4.2 Test Quality Objectives
Section 12.5 of this method will be utilized to determine the molecular weight of the stack on a wet basis. The formula found
in Method 3 section 12.3 will be utilized to determine the molecular weight of the stack gas on a dry basis.
CO
Target Analytes
Exhaust emission testing will be conducted for the following compounds: carbon monoxide (CO), oxides of nitrogen (NOx),
volatile organic compounds (VOCs), and oxygen (O2%).
Table 4.2 summarizes the test quality objectives specific that will be used to evaluate test data to a known degree of
accuracy.
Compounds
Table 4.2. Test Specific Target Analytes and Data Quality Objectives
Infrared Analysis
Expected
Concentration Range
Measurement
System Achievable
Minimum Detectable
Concentrations
Required
Measurement
System Accuracy
and Precision for
Test Application
(cm-1)
VOC as defined in 40 CFR Part 60
subpart JJJJ
2600-3200
0-100 ppm 0.9 ppm 1 ppm910-11502550-2950
*. Measured flue gas conditions at the sampling location including temperature, moisture content, and volumetric flow rate
will be included in test results.
Interfering Compounds
CO2 926-1150 0-10%0%n/a
Water Vapor 3200-3401 0-22%0.2%n/a
2700-2950 0-100 ppm 0.03 ppm 2 ppmNO2
EPA Method 2
EPA Method 3A
This method is applicable for the determination of the average velocity and the volumetric flow rate of a gas stream. Method
2C will be used for stacks with a diameter less than 12 inches.
This is a procedure for measuring oxygen (O2) and carbon dioxide (CO2) in stationary source emissions using a continuous
instrumental analyzer. Quality assurance and quality control requirements are included to assure that the tester collects data
of known quality. Documentation to these specific requirements for equipment, supplies, sample collection and analysis,
calculations, and data analysis will be included.
NO 1875-2138 0-1000 ppm 0.20 ppm 2 ppm
ASTM D6348-03
This extractive FTIR based field test method is used to quantify gas phase concentrations of multiple target analytes from
stationary source effluent. Because an FTIR analyzer is potentially capable of analyzing hundreds of compounds, this test
method is not analyte or source specific. The analytes’ detection levels, and data quality objectives are expected to change
for any particular testing situation. It is the responsibility of the tester to define the target analytes, the associated detection
limits for those analytes in the particular source effluent, and the required data quality objectives for each specific test
program. Provisions are included in this test method that require the tester to determine critical sampling system and
instrument operational parameters, and for the conduct of QA/QC procedures. Testers following this test method will
generate data that will allow an independent observer to verify the valid collection, identification, and quantification of the
subject target analytes. A heated sample line is used to collect the sample on a wet basis per ASTM D6348. Effluent
Moisture content is determined to within a 2% accuracy using the FTIR analytical algorithm.
4.0 Emissions Point Information
4 ppm1 ppm0-1200 ppm2000-2200
7
Great Plains Analytical Services, Inc.
Path
Length
Dilution
Factor
%
Recovery
4.93
10 92
A1)
A2)
A3)
A4)
A5)
A6)
A7)
Determination of System Performance Parameters - Noise Equivalent Absorbance, Line Position, Resolution, and
Analyte Spiking Technique
Required Pre-Test Procedures
FTIR Reference Spectra
Preparation of Analytical Quantification Algorithm
Determination of FTIR Measurement System Minimum Detectable Concentration
Test Plan Requirements
All information required per ASTM D6348, Annexes 1-7 will be provided in the final report. This information shall cover:
System Zero Nitrogen 65
Analyte Spike Recovery Propane 101.9 50
CTS Check entire system
System Recovery (Spike)
Data generated during the bench scale pre-test procedures will be presented in Table 5.1. Please note that Table 5.1 will
be presented in the final report with data collected from the actual field-testing source.
System Performance
(3A/D6348)Determines minimum sampling time During bias check
System Performance (3A)Within 3%During bias check
System response time
Drift
System Performance (D6348)Less than 2 % of permit limit Pre test
5.0 Quality Control Information (continued)
Mechanical Response Time Ethylene 101.2 42
System Response Time Propane 101.9 37
Table 5.1. Measurement System Capabilities
Parameter Measured Gas Concentration Equilibration Time
Path Length Ethylene 101.2
5.0 Quality Control Information
The following is a list of the QA/QC procedures performed. It is listed as to the process and method it pertains
to. Calibration sheets, calibration gases and any other testing equipment will be made available prior to the
start of testing. Upon completion of the assembled sampling system, a leak check will be conducted under
pressure or partial vacuum conditions to ensure the integrity of the sample collection system.
QA/QC Element
Traceability protocol
Probe material
Particulate filter
Table 5.0 QA/QC
Multiple Sample Points
Simultaneously (1/1A)83.3%, 50%, 16.6% from stack walls All stacks under 6"
Measurement from disturbances
Distance from stack walls
Sample Extraction (D6348)
Heated line
Manifold material
Process or Element
(Method)Acceptance Criteria Frequency
Calibration Gas 2% Certainty Every Test
Sample Extraction (1/1A)Pass system bias check Every test run
System Performance (D6348)
Verify line positions have not shifted by
more than 15% of the resolution, and the
resolution has not changed by more than
15% of that determined prior to testing.
Post TestLine position
System Performance (3A)Within 5%Before first test and
after last
Calibration
System bias check
System Performance (D6348)Within Tolerance Pre and post test
System Zero
CTS Check direct to analyzer
System Performance (D6348)Within Tolerance Pre Test
System Performance (D6348)Within 30% of effluent concentration Every test run
System Performance (3A)Within 10% of the Sample collected Every test
Stainless Steel Every Test
Velocity Flow Measurement
(2)
Manometer is leveled and visual
inspected
Sample Point Selection (1/1A)1/2 stack diameter downstream and 2
stack diameters upstream.Every test
Sample Extraction (D6348)Placed after heated probe Changed weekly
Heated to 180°C, introduces calibration
into sampling system at the probe outlet Every testProbe Box
Sample Extraction (3A/D6348)Sample kept above dew point at all
times.
Temp kept to 180°C at
all times. Visible
digital gauge
Sample Extraction (1/1A)
Every test run
Manometer
Manometer
Velocity Flow Measurement
(2)
System is back purged after last sample.
Another sample is taken and must be
within 5% of the last sample
Every test
8
Great Plains Analytical Services, Inc.
* Elevation, Barometric pressure ("HG), Ambient temperature °F, Humidity %, Dew Point °F
* Catalyst Inlet Temp °F, Catalyst Outlet Temp °F, Manifold Temp °F
* Exhaust Gas Temp °C
* RPM, Manifold Pressure ("HG)
* Horsepower (BHP) and Fuel Flow Rate (dscfh)
* Stack Diameter (")
* Sample location (" Downstream from Disturbance & " Upstream from Disturbance)
* Catalyst Pressure Drop ( Inches H2O)
* Moisture Percentage
* Volumetric Flow Rate
* AFR setpoints and reading
* Catalyst Manufacturer
* Number of elements
* Date of installation
* Date of last reconditioning or cleaning
1. Exhaust Volumetric flow Rate Determination by EPA Method 2
Qsd=3600*(1-B(ws))*V(s)*A*(T(std)/T(s))*P(s)/P(std)
V(s)= Absolute Stack Gas Velocity
A= Cross Sectional Area of Stack
T(std)= Standard Absolute Temperature
T(s)= Absolute Stack Temperature
P(s)= Absolute Stack Pressure
P(std)= Standard Absolute Pressure
(When Method 2 is used)
K=Pitot tube velocity Constant (85.49)
C=Velocity Pressure Coefficient
√ΔP= Square Root of differential Pressure of stack gas (inH2O)
T(s(avg))= Average Stack temp °R
M=Molecular Weight of stack gas, wet basis
P= Absolute stack gas Pressure
(LB/HR)*454
Engine Horsepower
(LB/HR)*24(HRS/DAY)*365(Days/YR)
2000(LB/TON)
3. Mass Emission Rates (TPY)
TPY =
g/hp-hr = lb/hr =
K*C*√(ΔP)*√(T(s(avg))+460)/√(M*P)V(s)=
6.0 Additional Information and Reporting
Additional parameters and atmospheric information will also be provided in the final report and will include:
The final report will contain all field test data including all pre and post calibration information. Final
concentrations will be reported in the permitted units of measure.
7.0 Example Calculations
2. Absolute Stack Gas Velocity V(s)
3. Mass Emission Rates (LBS./HR.)
((Mol Wgt)*(Qd dscfh)*(concentration
(385*106)
3. Mass Emission Rates (G./HP.-HR.)
9
Great Plains Analytical Services, Inc.
* Hardhat
* Steel-Toed Boots
* Safety Glasses
* Hearing Protection
* Fire-Retardant Clothing
* 4 - Safety Gloves
* 4 Gas Monitor
*
*
*
*
*
*
*
*
*
8.0 Health and Safety Concerns
In accordance with 40 CFR Part 60.8, the client must provide safe access to the unit for testing and observance.
Due to the nature of the source and the exposure to high temperatures, extreme caution will be observed in
order to avoid contact with the unit which may result in burns and or inhalation of exhaust emissions. GAS
personnel will sign in and out at all facilities, as well as undergo site specific safety training.
Probe: Heated probe assembly required by ASTM D6348.
Heated Line: Used for "Hot/Wet" sample to keep line above any dew point that would cause
moisture to drop out.
PSS: Allows precise heating of the sampling system.
Breakdown Of Schematic Diagram:
O2 Sensor: Zirconium Dioxide sensor to measure Oxygen per method 3A.
Gasmet FTIR: FTIR Analyzer for use with ASTM D6348
Flow Meter: Allows proper measurement of flow.
Data: Data acquisition system that allows for the acquisition of the infrared data, Oxygen data and
analysis of the resulting spectra.
Gas: Required calibration gases per ASTM D6348 and Method 3A.
Control Panel: Allows the control of flow throughout the system as required by ASTM D6348 and
Method 3A. Allows for introduction of calibration standards into the sampling system at the probe
outlet, upstream of the primary particulate filter.
Due to the remote location of the source unit, additional health & safety precautions will be observed such as
avoidance of slips, trips, falls, and heat exhaustion.
Figure 9.0 Sampling Schematic Diagram
Figure 9.0 Schematic Diagram
In addition, GAS will use the following safety equipment:
!
10
Great Plains Analytical Services, Inc.
**Note: Actual note parameters may differ due to the availability of such parameters at specific locations.
Attachment 11.0 Velocity Field Data
Attachment 10.0 Engine Parameter Data Sheet Diagram 1/53
Great Plains Analytical Services, Inc.
10.0 Engine Parameter Data Sheet
Company
Facility
Date
Elevation (ft)
Unit ID
Make
Model
Serial Number
Technician
Run 1 Run 2 Run 3 Average
Time:9:06 AM 10:17 AM 11:28 AM N/A
Engine Speed (RPM)1601 1600 1603 1601
Engine Hours 10568 10569 10570 10571
Catalyst (Yes or No)Yes Yes Yes Yes
Catalyst Manufacturer Murphy Murphy Murphy Murphy
# of Catalyst installed 1 1 1 1
Catalyst Element Installation date 7/22/16 7/22/16 7/22/16 7/22/16
Catalyst Inlet Temp °F 847 845 846 846
Catalyst Outlet Temp °F 878 879 780 846
Catalyst Pressure Drop H2O 1.50 1.50 1.50 1.50
Catalyst reconditioning or cleaning date New New New New
AFR Manufacturer/Type Murphy Murphy Murphy Murphy
AFR Setting (Targets Right Bank)17.00 17.00 17.00 17.00
AFR Readings NA NA NA NA
Intake Manifold Pressure (psi)4.40 4.50 4.50 4.47
Ambient Temp °F 76.00 79.00 83.00 79.33
Exhaust Gas Temp °F (From Probe)785.00 784.00 783.00 784.00
Intake Manifold Temp °F 85.00 85.00 85.00 85.00
Barometric Press ("HG)30.13 30.13 30.11 30.12
Fuel Flow Rate (dscf)587.00 586.63 587.73 587.12
Engine Load (BHP)72.05 72.00 72.14 72.06
Cottonwood 08E
Cummins
4,724
Whiting Oil & Gas Company
7/26/2016
73697207
ENG-01
5.9
Noel Arnim

01/03/2024

VIA Stack Test Report Submission:
https://utahgov.co1.qualtrics.com/jfe/form/SV_3dSxf7JSzy4jwGh

Rik Ombach
Manager, Minor Source Compliance
Utah Department of Environmental Quality
Division of Air Quality
195 North 1950 West
Salt Lake City, Utah 84116

RE: Notification of Performance Testing
Ovintiv USA Inc.
Duchesne County

Dear Mr. Ombach:

Ovintiv USA Inc. is providing notification of performance testing for the spark ignition internal combustion
engines that satisfy the following requirements for which the engines are subject:
• 40 CFR Part 60 Subpart JJJJ: 40 CFR §60.8 and §60.4243(b)(2)(i) initial test or
§60.4243(b)(2)(ii) initial test or subsequent test every 8,760 hours or 3 years, whichever
comes first; and
• Permit by Rule

Performance testing has been scheduled for the week of February 5, 2024.
Facility Latitude/
Longitude
CAERS
Source ID
Unit ID Manufacturer
& Model
Serial
Number
Amy UT 13-7 3-1 40.230446,
-110.043887
100742 803760 Doosan 14.6L EEZOG401147

The performance testing protocol is attached. If you have any questions, please contact me at 720-876-
3144 or [e-mail].

Sincerely,
Ryan Zillner
Senior Air Quality Engineer

Attachment
Great Plains Analytical Services, Inc.
Performance Test Protocol
40 CFR Part 60 Subpart JJJJ
Prepared by
303 West 3rd StreetElk City, OK 73644

!#"8'#": %( 7"<'.$ %$
16.7'.6 8(9 :7;<
Great Plains Analytical Services, Inc.
1.0 Introduction………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
1.1 Contact Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
2.0 Test Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
3.0 Method Synopsis………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….5
4.0 Emission Point Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
4.1 Target Analytes………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
4.2 Test Quality Objectives………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
5.0 Quality Control Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….7
6.0 Additional Information and Reporting………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….8
7.0 Example Calculations………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….8
8.0 Health and Safety Concerns………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….9
1.1 Contact Information………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
2.0 Source Information and Testing Dates………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….3
2.1 Testing Limits and Parameters (Federal)………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….4
2.2 Testing Limits and Parameters (State)………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….4
2.3 Additional Parameters………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….4
4.2 Test Specific Target Analytes and Data Quality Objectives………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….6
5.0 QA/QC………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….7
5.1 Measurement System Capabilities………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….7
3.1 Sample Port Location………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….5
3.2 Sample locations inside the stack………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….5
9.0 Sampling Schematic Diagram………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….9
10.0 Engine Parameter Data Sheet Diagram………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….10
11.0 Velocity Field Data Diagram………………………………………………………………………………………………………………………………………………………………………………………………….…………………………………………………………………………………………………….10
Table of Contents
Table(s)
Figure(s)
Protocol Attachment(s)
3
Great Plains Analytical Services, Inc.
2.0 Test Information (continued)
1.0 Introduction
Tests will consist of (3) 60 minute test runs.
The test will be conducted using a multi component gas analyzer that incorporates a Fourier Transform Infrared (FTIR) spectrometer. FTIR is state of the art technology. It is
designed to military specifications and allows simple calibration using only single component calibration gases.
370 17th Street, Suite 1700 Denver CO 80202
370 17th Street, Suite 1700 Denver CO 80202
4 Waterway Square Place, Suite 100 The Woodlands, TX
77380
Ovintiv USA Inc 720-876-3144 [e-mail]
Ovintiv USA Inc 281-847-6093 [e-mail]
1.1 Contact Information
2.0 Test Information
Date of
ManufactureTest Dates
[e-mail]
Ovintiv USA Inc.720-876-3017 [e-mail]
Table 2.0 Test Information and Testing Dates
GAS has been contracted by Ovintiv USA Inc. to conduct source testing services at located in County, . The purpose of this test plan is to document the test methods and procedures
that will be employed to collect and analyze exhaust gas emissions during performance testing of the internal combustion engines fueled by Natural Gas.
Contact
Macie McClellan
Physical Address
303 W 3rd St. Elk City, OK 73644GAS580-225-0403
Ryan Zillner
Brandon Lithgoe
Table 1.1 Contact Information
Thien Nguyen
Serial Number Location/Facility
Name Make and Model Horsepower RN#
Application Telephone Email Address
Source ID Engine
Classification
4
Great Plains Analytical Services, Inc.
g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2
g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2 g/hp-hr lb/hr TPY ppm
@15% O2
3A
D6348-03
1/1A
% H2O
Sample Location Inches (")
CO2, H2O, NOx, CO, VOC, and CH2O will be
measured using a Gasmet multigas FTIR analyzer in
accordance with ASTM Method D6348 when
applicable analytes are being tested for.
Footnote
Table 2.3 Additional Parameters
Reduction %
Reference Method 10/2
COOxygen (O2)%vd
Moisture
CH2O
320
Reduction %
Table 2.4 Testing Limits and Parameters (Reduction)
Source ID
Table 2.2 Testing Limits and Parameters (State)
Source ID
NOx CO VOC (NMNEHC)CH2O
Reference Method ASTM D6348-03 Reference Method ASTM D6348-03 Reference Method ASTM D6348-03 Reference Method ASTM D6348-03
CH2O
Reference Method ASTM D6348-03Reference Method ASTM D6348-03Reference Method ASTM D6348-03
Table 2.1 Testing Limits and Parameters (Federal)
Reference Method ASTM D6348-03Source ID
VOC (NMNEHC)NOx CO
5
Great Plains Analytical Services, Inc.
3.0 Method Synopsis
EPA Method 1
Figure 3.1
Figure 3.2
The purpose of the method is to provide guidance for the selection of sampling ports and traverse points at which sampling for air pollutants will be
performed pursuant to regulations set forth in this part. Method 1 may be modified as allowed in Subpart JJJJ & ZZZZ. Alternatively, for NOx, CO,
VOC, O2, and moisture measurement, ducts ≤6 inches in diameter may be sampled at a single point located at the duct centroid and ducts >6 and
≤12 inches in diameter may be sampled at 3 traverse points located at 16.7, 50.0, and 83.3% of the measurement line ('3-point long line'). If the
duct is >12 inches in diameter and the sampling port location meets the two and half-diameter criterion of Section 11.1.1 of Method 1 of 40 CFR
part 60, Appendix A, the duct may be sampled at '3-point long line'; otherwise, conduct the stratification testing and select sampling points
according to Section 8.1.2 of Method 7E of 40 CFR part 60, Appendix A."
For all stacks greater than 6" in diameter, GAS will use a sampling port that is located at a minimum of 2 stack diameters downstream from any
disturbance, and 1/2 stack diameter upstream from any disturbance.
For all stacks greater than 6" in diameter, GAS will sample at 3 points within the stack. These points will be located at 83.3%, 50%, and 16.7% of the
stack diameter.
1/2 diameter upstream
2 diameters downstream
Figure 3.2. Sample locations inside the stack
Actual diameter
Figure 3.1. Sample Port Location
6
Great Plains Analytical Services, Inc.
4.1 Target Analytes
4.2 Test Quality Objectives
Section 12.5 of this method will be utilized to determine the molecular weight of the stack on a wet basis. The formula found
in Method 3 section 12.3 will be utilized to determine the molecular weight of the stack gas on a dry basis.
CO
Target Analytes
Exhaust emission testing will be conducted for the following compounds: carbon monoxide (CO), oxides of nitrogen (NOx),
volatile organic compounds (VOCs), and oxygen (O2%).
Table 4.2 summarizes the test quality objectives specific that will be used to evaluate test data to a known degree of
accuracy.
Compounds
Table 4.2. Test Specific Target Analytes and Data Quality Objectives
Infrared Analysis
Expected
Concentration Range
Measurement
System Achievable
Minimum Detectable
Concentrations
Required
Measurement
System Accuracy
and Precision for
Test Application
(cm-1)
VOC as defined in 40 CFR Part 60
subpart JJJJ
2600-3200
0-100 ppm 0.9 ppm 1 ppm910-11502550-2950
*. Measured flue gas conditions at the sampling location including temperature, moisture content, and volumetric flow rate
will be included in test results.
Interfering Compounds
CO2 926-1150 0-10%0%n/a
Water Vapor 3200-3401 0-22%0.2%n/a
2700-2950 0-100 ppm 0.03 ppm 2 ppmNO2
EPA Method 2
EPA Method 3A
This method is applicable for the determination of the average velocity and the volumetric flow rate of a gas stream. Method
2C will be used for stacks with a diameter less than 12 inches.
This is a procedure for measuring oxygen (O2) and carbon dioxide (CO2) in stationary source emissions using a continuous
instrumental analyzer. Quality assurance and quality control requirements are included to assure that the tester collects data
of known quality. Documentation to these specific requirements for equipment, supplies, sample collection and analysis,
calculations, and data analysis will be included.
NO 1875-2138 0-1000 ppm 0.20 ppm 2 ppm
ASTM D6348-03
This extractive FTIR based field test method is used to quantify gas phase concentrations of multiple target analytes from
stationary source effluent. Because an FTIR analyzer is potentially capable of analyzing hundreds of compounds, this test
method is not analyte or source specific. The analytes’ detection levels, and data quality objectives are expected to change
for any particular testing situation. It is the responsibility of the tester to define the target analytes, the associated detection
limits for those analytes in the particular source effluent, and the required data quality objectives for each specific test
program. Provisions are included in this test method that require the tester to determine critical sampling system and
instrument operational parameters, and for the conduct of QA/QC procedures. Testers following this test method will
generate data that will allow an independent observer to verify the valid collection, identification, and quantification of the
subject target analytes. A heated sample line is used to collect the sample on a wet basis per ASTM D6348. Effluent
Moisture content is determined to within a 2% accuracy using the FTIR analytical algorithm.
4.0 Emissions Point Information
4 ppm1 ppm0-1200 ppm2000-2200
7
Great Plains Analytical Services, Inc.
Path
Length
Dilution
Factor
%
Recovery
4.93
10 92
A1)
A2)
A3)
A4)
A5)
A6)
A7)
Determination of System Performance Parameters - Noise Equivalent Absorbance, Line Position, Resolution, and
Analyte Spiking Technique
Required Pre-Test Procedures
FTIR Reference Spectra
Preparation of Analytical Quantification Algorithm
Determination of FTIR Measurement System Minimum Detectable Concentration
Test Plan Requirements
All information required per ASTM D6348, Annexes 1-7 will be provided in the final report. This information shall cover:
System Zero Nitrogen 65
Analyte Spike Recovery Propane 101.9 50
CTS Check entire system
System Recovery (Spike)
Data generated during the bench scale pre-test procedures will be presented in Table 5.1. Please note that Table 5.1 will
be presented in the final report with data collected from the actual field-testing source.
System Performance
(3A/D6348)Determines minimum sampling time During bias check
System Performance (3A)Within 3%During bias check
System response time
Drift
System Performance (D6348)Less than 2 % of permit limit Pre test
5.0 Quality Control Information (continued)
Mechanical Response Time Ethylene 101.2 42
System Response Time Propane 101.9 37
Table 5.1. Measurement System Capabilities
Parameter Measured Gas Concentration Equilibration Time
Path Length Ethylene 101.2
5.0 Quality Control Information
The following is a list of the QA/QC procedures performed. It is listed as to the process and method it pertains
to. Calibration sheets, calibration gases and any other testing equipment will be made available prior to the
start of testing. Upon completion of the assembled sampling system, a leak check will be conducted under
pressure or partial vacuum conditions to ensure the integrity of the sample collection system.
QA/QC Element
Traceability protocol
Probe material
Particulate filter
Table 5.0 QA/QC
Multiple Sample Points
Simultaneously (1/1A)83.3%, 50%, 16.6% from stack walls All stacks under 6"
Measurement from disturbances
Distance from stack walls
Sample Extraction (D6348)
Heated line
Manifold material
Process or Element
(Method)Acceptance Criteria Frequency
Calibration Gas 2% Certainty Every Test
Sample Extraction (1/1A)Pass system bias check Every test run
System Performance (D6348)
Verify line positions have not shifted by
more than 15% of the resolution, and the
resolution has not changed by more than
15% of that determined prior to testing.
Post TestLine position
System Performance (3A)Within 5%Before first test and
after last
Calibration
System bias check
System Performance (D6348)Within Tolerance Pre and post test
System Zero
CTS Check direct to analyzer
System Performance (D6348)Within Tolerance Pre Test
System Performance (D6348)Within 30% of effluent concentration Every test run
System Performance (3A)Within 10% of the Sample collected Every test
Stainless Steel Every Test
Velocity Flow Measurement
(2)
Manometer is leveled and visual
inspected
Sample Point Selection (1/1A)1/2 stack diameter downstream and 2
stack diameters upstream.Every test
Sample Extraction (D6348)Placed after heated probe Changed weekly
Heated to 180°C, introduces calibration
into sampling system at the probe outlet Every testProbe Box
Sample Extraction (3A/D6348)Sample kept above dew point at all
times.
Temp kept to 180°C at
all times. Visible
digital gauge
Sample Extraction (1/1A)
Every test run
Manometer
Manometer
Velocity Flow Measurement
(2)
System is back purged after last sample.
Another sample is taken and must be
within 5% of the last sample
Every test
8
Great Plains Analytical Services, Inc.
* Elevation, Barometric pressure ("HG), Ambient temperature °F, Humidity %, Dew Point °F
* Catalyst Inlet Temp °F, Catalyst Outlet Temp °F, Manifold Temp °F
* Exhaust Gas Temp °C
* RPM, Manifold Pressure ("HG)
* Horsepower (BHP) and Fuel Flow Rate (dscfh)
* Stack Diameter (")
* Sample location (" Downstream from Disturbance & " Upstream from Disturbance)
* Catalyst Pressure Drop ( Inches H2O)
* Moisture Percentage
* Volumetric Flow Rate
* AFR setpoints and reading
* Catalyst Manufacturer
* Number of elements
* Date of installation
* Date of last reconditioning or cleaning
1. Exhaust Volumetric flow Rate Determination by EPA Method 2
Qsd=3600*(1-B(ws))*V(s)*A*(T(std)/T(s))*P(s)/P(std)
V(s)= Absolute Stack Gas Velocity
A= Cross Sectional Area of Stack
T(std)= Standard Absolute Temperature
T(s)= Absolute Stack Temperature
P(s)= Absolute Stack Pressure
P(std)= Standard Absolute Pressure
(When Method 2 is used)
K=Pitot tube velocity Constant (85.49)
C=Velocity Pressure Coefficient
√ΔP= Square Root of differential Pressure of stack gas (inH2O)
T(s(avg))= Average Stack temp °R
M=Molecular Weight of stack gas, wet basis
P= Absolute stack gas Pressure
(LB/HR)*454
Engine Horsepower
(LB/HR)*24(HRS/DAY)*365(Days/YR)
2000(LB/TON)
3. Mass Emission Rates (TPY)
TPY =
g/hp-hr = lb/hr =
K*C*√(ΔP)*√(T(s(avg))+460)/√(M*P)V(s)=
6.0 Additional Information and Reporting
Additional parameters and atmospheric information will also be provided in the final report and will include:
The final report will contain all field test data including all pre and post calibration information. Final
concentrations will be reported in the permitted units of measure.
7.0 Example Calculations
2. Absolute Stack Gas Velocity V(s)
3. Mass Emission Rates (LBS./HR.)
((Mol Wgt)*(Qd dscfh)*(concentration
(385*106)
3. Mass Emission Rates (G./HP.-HR.)
9
Great Plains Analytical Services, Inc.
* Hardhat
* Steel-Toed Boots
* Safety Glasses
* Hearing Protection
* Fire-Retardant Clothing
* 4 - Safety Gloves
* 4 Gas Monitor
*
*
*
*
*
*
*
*
*
8.0 Health and Safety Concerns
In accordance with 40 CFR Part 60.8, the client must provide safe access to the unit for testing and observance.
Due to the nature of the source and the exposure to high temperatures, extreme caution will be observed in
order to avoid contact with the unit which may result in burns and or inhalation of exhaust emissions. GAS
personnel will sign in and out at all facilities, as well as undergo site specific safety training.
Probe: Heated probe assembly required by ASTM D6348.
Heated Line: Used for "Hot/Wet" sample to keep line above any dew point that would cause
moisture to drop out.
PSS: Allows precise heating of the sampling system.
Breakdown Of Schematic Diagram:
O2 Sensor: Zirconium Dioxide sensor to measure Oxygen per method 3A.
Gasmet FTIR: FTIR Analyzer for use with ASTM D6348
Flow Meter: Allows proper measurement of flow.
Data: Data acquisition system that allows for the acquisition of the infrared data, Oxygen data and
analysis of the resulting spectra.
Gas: Required calibration gases per ASTM D6348 and Method 3A.
Control Panel: Allows the control of flow throughout the system as required by ASTM D6348 and
Method 3A. Allows for introduction of calibration standards into the sampling system at the probe
outlet, upstream of the primary particulate filter.
Due to the remote location of the source unit, additional health & safety precautions will be observed such as
avoidance of slips, trips, falls, and heat exhaustion.
Figure 9.0 Sampling Schematic Diagram
Figure 9.0 Schematic Diagram
In addition, GAS will use the following safety equipment:
!
10
Great Plains Analytical Services, Inc.
**Note: Actual note parameters may differ due to the availability of such parameters at specific locations.
Attachment 11.0 Velocity Field Data
Attachment 10.0 Engine Parameter Data Sheet Diagram 1/53
Great Plains Analytical Services, Inc.
10.0 Engine Parameter Data Sheet
Company
Facility
Date
Elevation (ft)
Unit ID
Make
Model
Serial Number
Technician
Run 1 Run 2 Run 3 Average
Time:9:06 AM 10:17 AM 11:28 AM N/A
Engine Speed (RPM)1601 1600 1603 1601
Engine Hours 10568 10569 10570 10571
Catalyst (Yes or No)Yes Yes Yes Yes
Catalyst Manufacturer Murphy Murphy Murphy Murphy
# of Catalyst installed 1 1 1 1
Catalyst Element Installation date 7/22/16 7/22/16 7/22/16 7/22/16
Catalyst Inlet Temp °F 847 845 846 846
Catalyst Outlet Temp °F 878 879 780 846
Catalyst Pressure Drop H2O 1.50 1.50 1.50 1.50
Catalyst reconditioning or cleaning date New New New New
AFR Manufacturer/Type Murphy Murphy Murphy Murphy
AFR Setting (Targets Right Bank)17.00 17.00 17.00 17.00
AFR Readings NA NA NA NA
Intake Manifold Pressure (psi)4.40 4.50 4.50 4.47
Ambient Temp °F 76.00 79.00 83.00 79.33
Exhaust Gas Temp °F (From Probe)785.00 784.00 783.00 784.00
Intake Manifold Temp °F 85.00 85.00 85.00 85.00
Barometric Press ("HG)30.13 30.13 30.11 30.12
Fuel Flow Rate (dscf)587.00 586.63 587.73 587.12
Engine Load (BHP)72.05 72.00 72.14 72.06
Cottonwood 08E
Cummins
4,724
Whiting Oil & Gas Company
7/26/2016
73697207
ENG-01
5.9
Noel Arnim